Uniden XCA750 Manual do Utilizador

6.Plug the AC Adapter into astandard 230-240V AC walloutlet.AUse only the UnidenAC Adapter supplied withthis phone.’Direct Wall MountingYou can mount

3.Place the cord inside themolded channel on thebottom of the Base Unit.4.Plug the AC Adapter into theBase Unit.5.Place the AC Adapter cordinside the

Setting the Handset RetainerThe Handset Retainer holds the Handset in place if your phone is mountedon a wall. The steps below describe how to remove

2.Slide the battery compartmentcover down.Setting Up Your PhoneExtending the AntennaBefore using your phone, be sure to fully extend the antenna to th

Cleaning the Battery ContactsTo maintain a good charge, it is important to clean all charging contacts onthe Handset and Base Unit about once a month.

2.Make sure the charge LEDlights. If the LED doesn’tlight, check to see that theAC Adapter is plugged in,and that the Handset ismaking good contact wi

If the talk/batt low LED begins to flash, the phone is programmed to limit itsfunctions to save power. The table below describes what to do to return

To adjust the Base speakervolume, press the volumecontrol switch to achieve thedesired setting.Automatic Digital Code SecurityTo avoid unauthorised ca

If the Base Unit loses power while the Handset is off the Base, the DigitalCode may be erased. When this happens, the Handset will not function. Toree

Changing Channels, Flash, and Page/FindProgramming Your PhoneTo change channels or access call waiting while the phone is in use, or touse the one-way

PRECAUTIONSBefore you read anything else,please observe the following:WARNING!Uniden Corporation DOES NOT represent this unit to be waterproof.To redu

3.Enter the number you want to@)@@a@a@store (up to 16 digits).4.If a pause is needed during@Qdialing to access a longdistance service, press Q .@@@a@a

4.Press tone on the Handset.(# button)I5.Enter the number to be dialedin tone mode.@@[email protected] a pause is needed duringdialing to access a longQ@@O@dista

4.Press the memory locationnumber (0-9).Chain DialingOn certain occasions, after dialing a number, you may be requested by theparty or service you are

The Integrated Answering SystemAnswering System SetupThe XCA650/XCA750 has a built-in Answering System which answersincoming calls and records you mes

4.To turn the AnsweringSystem off, press BThe talk/batt low LED lightsgreen, The current Time andDay Stamp and number ofnew messages recorded isannoun

2.Press 0.Then enter the number whichcorresponds to the day.3.Enter the two-digit numberfor the hour (01-12) and theminute (00-59)4.To set AM, press *

Base Operation1.Press l .The speaker beeps, and theTime and Day Stamp isannounced.Setting Your Outgoing Message (OGM)When you receive a call, the Answ

3.Press m to stop recording.The message replays in theHandset receiver.4.Press a again to returnto Standby.The talk/batt low LED turns off.Base Operat

Selecting a Preset OGMAfter you have recorded an outgoing message, you can set your AnsweringSystem to play either a preset message or your outgoing m

Using the Reset ButtonThe RESET button is used to erase all recorded outgoing messages and anymessages which are saved in memory. Pressing RESET does

4.Press a to return toStandby.The talk/batt low LED goesOff.Base OperationWhen the Message Counter LED flashes,you have received new messages.1.Press

3.When all messages have2.When all messages haveplayed, a long tone soundsplayed, a long tone soundsfollowed by thefollowed by theannouncement “End of

2.Press b to review yourmessages.3.Press 44 at anytime to replaya message.Nofe: Pressing ti during amessage returns the systemto the beginning of that

Skipping a MessageHandset Operation1. Press remote.2.Press b to review yourmessages.3.Press N at anytime to skip tothe next message.Note: Each time B

3.Press m at anytime to stopreviewing messages andreturn to Standby.The Message Counter LEDshows the total number ofmessages.4.When all messages havep

2.If you decide to delete amessage, press and releaseze;tyt$e during theThe system beeps andimmediate/y goes to the nextmessage.Note: When you press 0

Message Full Indication2.Press ?.The XCA650/XCA750 has a maximum record time of 20 minutes or up to40 incoming message. When the memory is full, the A

Screening Incoming CallsLeaving a Memo MessageIf you receive a call while your Answering System is on, you can listen to theincoming message on the Ba

Recording a Telephone Conversation*WARNINGUse of this device for monitoring telephone conversations is not permissibleunder New Zealand law, unless:-(

2.Press *.3.Press your four-digit code.;;;;;;;;l;,=ue@9ez9 @ @94.Press & again.You will hear a long tonewhich indicates that the newcode is saved,

ContentsImportant Safety Instructions...3Battery Safety Precautions...4Introduction...

5.Use this chart to select thefunction you want.6.When you’ve finished, hangup to exit the system.Your Answering Systemautomatically returns toStandby

Answering System Troubleshooting ChartSpecificationsProblemSuggestionAnswering System does not work.l .pke sure that the Base Unit is pluggedl Make su

WARRANTYUNIDEN XCA650/XCA750 1 YEAR WARRANTY(Batteries and Accessories are covered for 90 Days ONLY)Note: Please keep your sales docket as it provide

Important Safety InstructionsWhen using your telephone equipment, these basic safety precautionsshould always be followed to reduce the risk of fire,

IntroductionIncluded with the XCA65O!!CA750Congratulations on your purchase of the Uniden XCA650/XCA750Cordless Telephone. These phones are designed t

Important Electrical ConsiderationsRadio lntetferenceUnplug all electrical appliances when you know an electrical storm isapproaching. Lightning can p

InstallationSelecting a LocationBefore choosing a location for your new phone, there are some importantguidelines you should consider:lThe location sh

Desk or Tabletop Installation1.Place the Base on a desk ortabletop.2.Plug one end of thetelephone cord into theTEL LINE jack on the BaseUnit.3.Plug th